| |
|
|
Reduced Prices!Sherline's Machine Tool, Packages and Chucks
LATHE ACCESSORIES
PART NO. |
PRODUCT NAME AND USE |
WT/LBS |
Our Price | Buy Now |
1074 |
STEADY REST (Supports the end of long work for center drilling) | .75 |
$38.00 |  |
1090 |
FOLLOWER REST (Supports thin work, keeps it from deflecting away from the cutter, moves with the lathe saddle to "follow" the work) | .75 |
$66.50 | |
1160 |
WW COLLET SET (Metric P/N 1178) (P/N 1161 included in set) (Collets are like small, individually sized chucks for holding a specific diameter tool or material. WW collets have a hole through the collet and drawbar to accept long material. Traditionally used by watch and clock makers. Sherline WW collets have a .312-.313 body size and .275-40 thread.) | .5 |
$85.50 | |
1161 |
WW COLLET ADAPTER & DRAWBAR (Included in collet set. Adapts WW taper to #1 Morse taper of Headstock) | .5 |
$47.50 | |
1162 |
DELUXE WW COLLET SET (Inch) (17 collets, adapter, drawbar, pot chucks, knockout bar, etc. in wooden case) | 3 |
$261.25 | |
1171 |
Oak WW Collect Box. Give your WW collects a fitting home. | 1 |
$30.40 | |
1179 |
DELUXE WW COLLET SET (Metric) (14 collets, pot chucks, etc. in wooden case. P/N 1161 included in set) | 3 |
$232.75 | |
|
1180 |
COMPLETE METRIC WW COLLET SET with 78 collets sized from .3 mm to 8.0 mm by .1 mm increments plus a blank collet. The set is contained in a P/N 1171 oak collet box with 96-hole oak insert. |
4 |
$888.25 | |
1182 |
BULLNOSE LIVE CENTER. (Supports tubing or stock with a large end hole when turning between centers. Dual preloaded bearings.) | .75 |
$76.00 | |
1185 |
VERTICAL MILLING TABLE (Metric P/N 1184) (Mounts to lathe or mill table to move work up and down. Has 2.25" of vertical travel) | .75 |
$114.00 | |
1191 |
LIVE CENTER (Ball bearings allow center to rotate with part to reduce friction when turning between centers) | .25 |
$38.00 | |
1201 |
ADJUSTABLE LIVE CENTER (Ball bearing live center adjusts for perfect centering of headstock and tailstock) | .5 |
$61.75 | |
1202 |
ADJUST. TAILSTOCK CHUCK ARBOR (Allows perfect centering of tailstock chuck in relation to headstock) | .5 |
$42.75 | |
1203 |
ADJUST. TAILSTOCK TOOL HOLDER (Allows perfect centering of round tools held in tailstock) | .5 |
$42.75 | |
1206 |
ADJUST. TAILSTOCK 1" DIE HOLDER w/ 13/16" bushing (Allows perfect centering of 1" or 13/16" threading dies) | .5 |
$57.00 | |
1220 |
TAILSTOCK SPINDLE EXTENDER (Designed for lathes built before July, 1996 to extend reach of tailstock spindle over table. Not needed on newer lathes) | .5 |
$38.00 | |
1230 |
#0 MORSE ARBOR TO 3/4-16 CHUCK THREAD ADAPTER (Allows a 3- or 4-jaw chuck to be mounted on the tailstock spindle) | .25 |
$38.00 | |
1270 |
COMPOUND SLIDE (Redesigned, Replaces P/N 1080) (metric P/N 1280) (An alternate and more traditional way of turning tapers) | 1 |
$118.75 | |
1272 |
Compound Riser | .5 |
$33.25 |
|
1288 |
RISER ROCKER TOOL POST (The riser tool post is used to bring the cutting tool back to lathe centerline height when using a riser block to raise the headstock to turn larger parts. This particular tool post has a convenient "rocker" design that allows adjustment of the tool tip height) | .5 |
$38.00 | |
1289 |
RISER 3/8" INSERT HOLDER TOOL POST (A riser tool post is used to bring the cutting tool back to lathe centerline height when using a riser block to raise the headstock to turn larger diameter parts. The riser 3/8" insert tool post holds either a 3/8" square shank insert tool holder or a 3/8" round holder) | .5 |
$38.00 | |
1290 |
STEADY REST RISER (Lifts steady rest to match headstock when spacer block is in place. Used mainly by those who leave spacer blocks in place at all times on their lathe.) | .25 |
$47.50 | |
1291 |
SPACER BLOCK KIT (Lifts headstock 1.25" to allow parts up to 6" diameter to be turned. Includes extended riser rocker tool post) | 1.5 |
$66.50 | |
1292 |
TAILSTOCK RISER BLOCK (Lifts tailstock 1.25" for turning between centers with headstock riser block in place) | 1 |
$47.50 | |
2040 |
.7 mm WW COLLET | .05 |
$23.75 | |
2041 |
.8mm WW COLLET | .05 |
$23.75 | |
2042 |
1/32" WW COLLET | .05 |
$23.75 | |
2043 |
.9 mm WW COLLET | .05 |
$23.75 | |
2044 |
3/64" WW COLLET | .05 |
$23.75 | |
2046 |
1.0 mm WW COLLET | .05 |
$23.75 | |
2050 |
WW COLLET BLANK (Drill and split yourself to make your own custom collet) | .05 |
$9.25 | |
2051 |
1/16" WW COLLET | .05 |
$13.90 | |
2052 |
5/64" WW COLLET | .05 |
$13.90 | |
2053 |
3/32" WW COLLET | .05 |
$13.90 | |
2054 |
7/64" WW COLLET | .05 |
$13.90 | |
2055 |
1/8" WW COLLET | .05 |
$13.90 | |
2056 |
9/64" WW COLLET | .05 |
$13.90 | |
2057 |
5/32" WW COLLET | .05 |
$13.90 | |
2058 |
11/64" WW COLLET | .05 |
$13.90 | |
2059 |
3/16" WW COLLET | .05 |
$13.90 | |
2060 |
13/64" WW COLLET | .05 |
$13.90 | |
2061 |
7/32" WW COLLET | .05 |
$13.90 | |
2062 |
15/64" WW COLLET | .05 |
$13.90 | |
2063 |
1/4" WW COLLET | .05 |
$13.90 | |
2064 |
17/64" WW COLLET | .05 |
$13.90 | |
2065 |
9/32" WW COLLET | .05 |
$13.90 | |
2066 |
19/64" WW COLLET | .05 |
$13.90 | |
2067 |
5/16" WW COLLET | .05 |
$13.90 | |
2068 |
1.5MM WW COLLET | .05 |
$13.90 | |
2069 |
2.0MM WW COLLET | .05 |
$13.90 | |
2070 |
2.5MM WW COLLET | .05 |
$13.90 | |
2071 |
3.0MM WW COLLET | .05 |
$13.90 | |
2072 |
3.5MM WW COLLET | .05 |
$13.90 | |
2073 |
4.0MM WW COLLET | .05 |
$13.90 | |
2074 |
4.5MM WW COLLET | .05 |
$13.90 | |
2075 |
5.0MM WW COLLET | .05 |
$13.90 | |
2076 |
5.5MM WW COLLET | .05 |
$13.90 | |
2077 |
6.0MM WW COLLET | .05 |
$13.90 | |
2078 |
6.5MM WW COLLET | .05 |
$13.90 | |
2079 |
7.0MM WW COLLET | .05 |
$13.90 | |
2080 |
7.5MM WW COLLET | .05 |
$13.90 | |
2081 |
8.0MM WW COLLET | .05 |
$13.90 | |
2082 |
WW COLLET (Special Order .050 to .320) (Allow 3 weeks Delivery) | .05 |
$23.15 | |
2083 |
WW COLLET 1" BLANK (Make your own custom tool holder or collet that is held with the WW adapter and drawbar) | .15 |
$28.50 | |
2085 |
WW COLLET TAILSTOCK ADAPTER (Use with P/N 1203) (Allows WW collets to be held in the tailstock) | .25 |
$52.25 | |
2086 |
8mm COLLET TAILSTOCK ADAPTER (Use with P/N 1203) | .25 |
$57.00 | |
2090 |
8.0mm COLLET TO 3/4-16 THREAD (For mounting Sherline chuck on watchmaker's or jeweler's lathe that takes 8.0mm collets) | .5 |
$38.00 | |
2091 |
10mm "D" COLLET TO 3/4-16 THREAD (For mounting Sherline chuck on watchmaker's or jeweler's lathe that takes 10mm D collets) | .5 |
$42.75 | |
2092 |
8.0mm COLLET TO 3/8-24 THREAD (For mounting chuck with 3/8-24 thread on watchmaker's or jeweler's lathe that takes 8.0mm collets) | .5 |
$38.00 | |
2093 |
10.0mm COLLET TO 3/8-24 THREAD (For mounting chuck with 3/8-24 thread on watchmaker's or jeweler's lathe that takes 10mm D collets) | .5 |
$42.75 | |
2094 |
CLOCKMAKER'S GEAR CUTTING ARBOR, 7.0mm to Morse #1 (Arbor for use on watchmaker or jeweler's lathes to hold round gear cutter. Not for use on Sherline lathe) | .5 |
$57.00 | |
2095 |
CLOCKMAKER'S GEAR CUTTING ARBOR, 7.0mm to 10mm "D" Collet (Arbor for use on watchmaker's or jeweler's lathes to hold round gear cutter. Not for use on Sherline lathe) | .5 |
$57.00 | |
2096 |
CLOCKMAKER'S GEAR CUTTING ARBOR, 7.0mm to 8.0 mm WW Collet (Arbor for use on watchmaker's or jeweler's lathes to hold round gear cutter. Not for use on Sherline lathe) | .5 |
$57.00 | |
2101 |
1" COLLET POT CHUCK (See 2100) | .05 |
$25.65 | |
2102 |
1-1/4" COLLET POT CHUCK (See 2100) | .05 |
$28.50 | |
2103 |
10mm 3/4" COLLET POT CHUCK (See 2100) | .15 |
$33.25 | |
2104 |
1Omm 1" COLLET POT CHUCK (See 2100) | .15 |
$38.00 | |
2105 |
10mm 1-1/4" COLLET POT CHUCK (See 2100) | .15 |
$42.75 | |
2106 |
LIVE CENTER-TO-8mm COLLET (A live center for watchmaker's or jeweler's lathes.) | .15 |
$71.25 | |
2107 |
LIVE CENTER-TO-10mm COLLET (A live center for watchmaker's or jeweler's lathes.) | .25 |
$71.25 | |
2110 |
W.R. SMITH WATCHMAKER'S T-REST (Used on Sherline lathes to support a hand-held "graver", a traditional watchmaker's tool. Turns Sherline lathe into a first class watch or clock maker's lathe. Designed by famed craftsman W.R. Smith. Graver-making instructions included.) | 1 |
$190.00 | |
2200 |
RADIUS CUTTING ATTACHMENT (For cutting ball ends, convex and concave radii on ends of parts and even complete balls) | 1 |
$114.00 | |
2250 |
QUICK CHANGE TOOL POST w/ 3 holders (Saves time when changing tools. Holders included for 1/4" cutter, round boring tool and cutoff tool. Cutting tools not included.) | 3 |
$247.00 | |
2251 |
QUICK-CHANGE TOOL PAST RISER (Now your Sherline quick-change tool post system can be used with the riser blocks in place when turning larger diameter parts) | 1.75 |
$47.50 | |
2256 |
RIGHT-HAND 35° CARBIDE INSERT TOOL HOLDER (Includes one 55° insert) (Use in 7600 tool post. Carbide is used to cut hard-to-machine materials like stainless steel) | .15 |
$42.75 | |
2257 |
LEFT-HAND 35° CARBIDE INSERT TOOL HOLDER (Includes one 55° insert) (Use in 7600 tool post. Carbide is used to cut hard-to-machine materials like stainless steel) | .15 |
$42.75 | |
2258 |
PAIR OF RIGHT- and LEFT-HAND 35° INSERT TOOL HOLDERS (Includes one 55° insert per holder) (Replacement inserts, P/N 7605) (Save $20 by buying both LH and RH tools together) | .25 |
$66.50 | |
|
2259 |
80° INSERT 3/8" ROUND BORING TOOL, 1/2" min. hole, carbide insert included (Use w/ P/N 7600 tool post) | .15 | $57.00 | |
|
2260 |
55° INSERT 3/8" ROUND BORING TOOL, 3/4" min. hole, carbide insert included (Use w/ P/N 7600 tool post) | .15 | $57.00 | |
|
2261 |
PAIR OF ABOVE 80° (P/N 2259) AND 55° (P/N 2260) 3/8" ROUND BORING TOOLS w/ inserts | .25 | $90.25 | |
2280 |
1/4" QUICK-CHANGE TOOL BIT HOLDER (Incl. w/ 2250) | 1 |
$57.00 | |
2285 |
3/8" QUICK-CHANGE BORING TOOL HOLDER (Incl. w/ 2250) | 1 |
$57.00 | |
2290 |
QUICK-CHANGE CUTOFF TOOL HOLDER (Incl. w/ 2250) | 1 |
$76.00 | |
2295 |
CARBIDE INSERT HOLDER for QUICK-CHANGE TOOL POST | 1 |
$85.50 | |
3001 |
POWER FEED (120V.) (for 240V. see P/N 3011) (Single direction motor drives lathe leadscrew .9" per minute to provide smooth final cut on long parts. Not designed for use with thread cutting attachment.) | 5 |
$85.50 | |
3002 |
CUTOFF TOOL & HOLDER (for cutting off work piece from the raw stock from which it was turned. Often called a "parting tool".) | .25 |
$47.50 | |
3003 |
TWO-POSITION TOOL POST (Holds two 1/4" cutting tools for quicker tool changes) | .25 |
$15.20 | |
3004 |
KNURLING TOOL HOLDER (Makes knurled finishes. Includes one set of spiral knurls. Other sizes and patterns available) | .25 |
$71.25 | |
3005 |
1/4" SQ. HIGH SPEED STEEL TOOL BLANK (Sharpen yourself on a bench grinder for standard or custom-shaped tools) | .05 |
$2.85 | |
3006 |
CARBIDE TOOL SET (3 PC) (LH, RH, 60° THREADING) (Carbide tips are brazed to 1/4" tool shanks. For cutting hard materials) | .25 |
$19.00 | |
3007 |
HIGH SPEED STEEL TOOL SET (3 PC) (LH, RH, BORING) (Pre-sharpened to save you time. For cutting most materials) | .25 |
$23.75 | |
3008 |
TWO-POSITION TOOL POST, 5/16" - 3/8" (Holds 5/16" tool on one side, 3/8" on other side. Allows use of tools other than 1/4") | .25 |
$23.75 | |
3009 |
CUTTING TOOL HEIGHT GAUGE (Used to assure tool tip on resharpened tools is set to proper centerline height. Works with both regular or riser toolpost) | .5 |
$17.10 | |
3011 |
POWER FEED (240V.) (See P/N 3001) | 5 |
$95.00 | |
3016 |
CUTOFF TOOL REAR MOUNTING BLOCK (Allows 3002 cutoff tool to be mounted on "back" side of crosslide where it is out of the way and can be left in place for easy parting off. Cutoff blade mounts upside down for use in this position) | .15 |
$14.25 | |
3017 |
CROSSLIDE ACCESSORY PLATE (Strengthens and protects lathe table when used for milling with vertical milling column. Not for use during lathe operations as tool post height will be incorrect.) | 1 |
$38.00 | |
3018 |
REAR MOUNT CUTOFF TOOL AND HOLDER | .25 |
$47.50 | |
3035 |
SPUR DRIVER (A quick way to drive wood parts when turning between centers.) | .25 |
$23.75 | |
3038 |
WOOD TOOL REST (3" & 5" REST) (Supports hand-held wood cutting tools for wood turning) | .75 |
$52.25 | |
3047 |
EXTENDED WOOD TOOL REST SET (For use w/ 1291) (Like 3038 only with longer shafts to match height of headstock with riser block in place) | .75 |
$57.00 | |
3050 |
VERTICAL MILLING COLUMN (Metric P/N 3053) (Converts your lathe into a 3-axis mill in less than 30 seconds.) | 8 |
$142.50 | |
3057 |
ROCKER TOOL POST (Rocking insert with two screws allows adjustment of tool tip height for accurate turning. Eliminates shimming. Included on Model 4400/4410 lathes) | .5 |
$28.50 | |
3100 |
THREAD-CUTTING ATTACHMENT (Being able to cut threads on your lathe frees you from the expense of purchasing a lot of expensive taps and dies for non-standard size threads. Cut just about any thread, inch or metric, using this set of change gears. Hand crank wheel included) | 3 |
$118.75 | |
3480 |
VERTICAL MILLING COLUMN W/ADJ. HANDWHEEL (Metric P/N 3485) (Turns lathe into a mill in less than 30 seconds. Normally used with 4500 or 4400 lathes to match adj. Zero handwheels) | 8 |
$161.50 | |
3580 |
MULTI-DIRECTION DELUXE VERTICAL MILLING COLUMN (Turns your lathe into an 8-direction mill in 30 seconds) | 10 |
$356.25 | |
3585 |
MULTI-DIRECTION DELUXE VERT. MILLING COLUMN (Metric) | 10 |
$356.25 | |
4150 |
15" LATHE VINYL COVER (Protect your 4000-series lathe from dust and grit) | .25 |
$9.50 | |
4151 |
24" LATHE VINYL DUST COVER (Protect your 4400-series lathe from dust and grit) | .25 |
$11.40 | |
5201 |
XYZ BASE (10") (Inch) (Add the motor/speed control from your lathe and you have a model 5000 mill) |
26 |
$389.50 | |
5211 |
XYZ BASE (10") (Metric) (Add the motor/speed control from you lathe and you have a model 5100 mill) |
26 |
$389.50 | |
6720 |
CNC UPGRADE KIT, 4000 or 4500 LATHE (Metric P/N 6725) (Replaces the handwheels with stepper motor mounts, ready for the installation of your own stepper motors and CNC control.) | 2 |
$190.00 | |
6730 |
CNC UPGRADE KIT, 4400 LATHE (Metric P/N 6735) (Replaces the handwheels with stepper motor mounts, ready for the installation of your own stepper motors and CNC control.) | 2 |
$199.50 | |
6780 |
CNC UPGRADE KIT, leadscrew axis only, 4000/4500-series lathes (Metric P/N 6785 | 1 |
$123.50 | |
6790 |
CNC UPGRADE KIT, leadscrew axis only, 4400-series lathes (Metric P/N 6795) | 1 |
$133.00 | |
7600 |
3/8" INSERT HOLDER TOOL POST (Has side slot to hold 3/8" shank cutting tool holders plus a 3/8" round hole to hold round boring bars.) | .25 |
$19.00 | |
7610 |
55° NEGATIVE RAKE INSERT HOLDER w/ insert (Holds carbide tips for cutting hard materials like stainless steel. 5° angle provides negative clearance for the cutter, which is supported all the way down to the table for rigidity.) | .25 |
$57.00 | |
7612 |
REPLACEMENT 4-SIDED CARBIDE INSERT TOOL (for 7610) | .05 |
$12.35 | |
7620 |
SINGLE FLUTE INSERT FLY CUTTER (Carbide insert cuts hard materials. Also is a good compromise between a fly cutter and an end mill, because it will cut a 1-1/8" wide path while still being able to cut right up to a shoulder.) | .5 |
$57.00 | |
7622 |
REPLACEMENT 2-SIDED CARBIDE TIP (for 7620) | .05 |
$12.35 | |
8200 |
2-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE (inch) (Metric P/N 8260) (Reads table position to .0005", electronic compensation for backlash) | 2.5 |
$308.75 | |
8220 |
2-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE without READOUT BOX (For those who already have a Mill DRO package) (Inch) (Metric P/N 8225) (Reads table position to .0005", electronic compensation for backlash) | 2 |
$156.75 | |
| 8870 | CNC LATHE LEADSCREW POWER FEED, 4000/4500 LATHES, w/ STEPPER MOTOR, MOUNT, COUPLER, CONTROLLER, CABLES, POWER SUPPLY AND REPLACEMENT 15" LEADSCREW (Replaces handwheel on long leadscrew of lathe with stepper motor mount and stepper motor. Motor is driven by self-contained computer/keypad unit and power supply to move the saddle from .0005 to 9.9995". Includes drill block for locating mounting holes. Can be daisy chained with other Sherline linear or rotary controllers.) Inch version only | 7 | 494.00 | |
|
8880
|
CNC LATHE LEADSCREW POWER FEED, 4400 LATHES, w/ STEPPER MOTOR, MOUNT, COUPLER, CONTROLLER, CABLES, POWER SUPPLY AND REPLACEMENT 24" LEADSCREW (See description for 8870 above.) |
7
|
$503.50
|
|
| 116000 | WW COLLET BLANK, Large Head | .05 | $10.45 | |
| 116001 | 1/64" WW COLLET | .05 | $38.00 | |
| 116002 | 1/32" WW COLLET | .05 | $30.40 | |
| 116003 | 3/64" WW COLLET | .05 | $19.95 | |
| 116004 through 116020 | WW COLLETS from size 1/16" to 5/16" by 64ths. | .05 | $16.15 | |
| 117801 | .1 mm WW COLLET | .05 | 33.25 | |
| 117802 | .2 mm WW COLLET | .05 | 33.25 | |
| 117803 through 117808 | WW COLLETS from size .3mm through .8 mm by .1 mm increments. | .05 | $38.00 | |
| 117809 through 117814 | WW COLLETS from size .9mm through 1.4 mm by .1 mm increments. | .05 | $30.04 | |
| 117815 through 117880 | WW COLLETS from size 1.5 mm through 8.0 mm by .1 mm increments. | .05 | $16.15 | |
VERTICAL MILLING MACHINE ACCESSORIES
PART NO. |
PRODUCT NAME AND USE |
WT/LBS |
Our Price | Buy Now |
1164 |
(WW) Collet Fixture (Allows WW collets with .312-.313 body to be held on face of rotary table or mill table.) | 1 |
$99.75 | |
1165 |
(8 mm) Collet Fixture (Allows WW collets with .314-.315 body to be held on face of rotary table or mill table.) | 1 |
$109.25 | |
1187 |
CHUCK-TO-T-SLOT ADAPTER (Allows 3- or 4-jaw chuck to be quickly screwed to mill table.) | .05 |
$7.10 | |
1297 |
MILL HEADSTOCK SPACER BLOCK (Same as riser block for lathe, but without tool post. Adds 1.25" of throat distance when milling) | .75 |
$42.75 | |
|
1300 |
MILL COLUMN SPACER BLOCK (Raises column base 2" for greater Z-axis clearance. Includes longer bolts for mounting.) |
1.50 |
$38.00 | |
2045 |
HEX AND OCTAGON INDEX BLOCK SET (Fits in mill vise to allow simple indexing of 2, 3, 4, 6 or 8 sides or hole patterns) | 2 |
$57.00 | |
3012 |
HOLD-DOWN SET (Simple strap clamp set for clamping parts to table for milling. Includes 2 clamps, T-nuts and assorted length bolts) | .4 |
$23.75 | |
3013 |
STEP BLOCK HOLD-DOWN SET (This is a smaller version of the sets used on most full-size mills. Quicker to use than 3012 and holds larger parts. Stepped blocks interlock to adjust height quickly. Spare block included to be cut to custom sizes) | 1 |
$38.00 | |
3052 |
FLY CUTTER (For quickly milling large, flat surfaces.) | .5 |
$33.25 | |
3054 |
BORING HEAD (For enlarging holes to a precise inside diameter, uses 3/8" round boring tools) | .5 |
$66.50 | |
3055 |
MORSE #1 BLANK (Turn on lathe and/or mill slots to make your own custom fly cutter, slitting saw holder or special tool holder) | .5 |
$15.20 | |
3058 |
4-JAW HOLD DOWN SET (Two angle clamps with T-nuts to clamp 4-jaw vise to any position on mill table. Included with 3551 mill vise) | .15 |
$5.70 | |
3060 |
MILLING COLLET SET (3 PC), (Metric P/N 3090) (1/8", 3/16", 1/4") (Milling collets have a #1 Morse taper and are pulled into the headstock with a drawbolt. They do not have a through hole like WW collets. They are used to hold specific size end mills or cutters.) | .15 |
$42.75 | |
3061 |
BORING TOOL—Max. Depth .600, Min. Hole 1/4") (Use w/ P/N 3054 boring head) | .15 |
$14.25 | |
3063 |
BORING TOOL—Max. Depth 1", Min. Hole 5/16" (Use with P/N 3054 boring head) | .15 |
$14.25 | |
3064 |
BORING TOOL—Max. Depth 1.5", Min. Hole 5/16" (Use w/ 3054 boring head) | .15 |
$17.10 | |
3065 |
SLITTING SAW HOLDER (Holds small, round sawblades for cutting thin slots) | .25 |
$38.00 | |
3075 |
5/16" END MILL HOLDER | .5 |
$28.50 | |
3076 |
6.0mm END MILL HOLDER | .5 |
$28.50 | |
3077 |
8.0mm END MILL HOLDER | .5 |
$28.50 | |
3078 |
10.0MM END MILL HOLDER (Most common size metric tool holder) | .5 |
$28.50 | |
3079 |
3/8" END MILL HOLDER (Most common size inch tool holder. 3/8" end mills are available from many sources and are, therefore, the least expensive and available in the largest selection.) | .5 |
$28.50 | |
6079 |
1/4" END MILL HOLDER (Holds end mills in 3080 set) | .5 |
$28.50 | |
6080 |
3/16" END MILL HOLDER | .5 |
$28.50 | |
6081 |
1/8" END MILL HOLDER | .5 |
$28.50 | |
3080 |
END MILL SET (1/4" SHK) (1/8", 3/16", 1/4") | .05 |
$28.50 | |
3087 |
3/32" MILL COLLET | .05 |
$19.00 | |
3089 |
5/32" MILL COLLET | .05 |
